Ghost 2 Immobiliser Reviews
The Ghost 2 immobiliser uses cutting-edge technology to prevent car theft. This discreet device is unnoticeable by thieves and only turns on the engine when a PIN or app is entered.
It's weatherproof and connects to the CAN data network of your vehicle. It also comes with a service/valet mode, which allows you to start your car for a short period when it's in the garage for cleaning or servicing.
Easy to install
The Ghost immobiliser protects your car from key theft, cloning and hacking. It is an PIN code system that is integrated into your vehicle's electronic control unit, making it hard for thieves to identify. Unlike traditional immobilisers, it does not require any specific keys or sensors. It is completely hidden from view with no LEDs or signals to give away its presence. It is also a lot cheaper than replacing an ECU or installing an entirely new key fob. It also could lower the cost of your monthly insurance.
Follow the instructions of the manufacturer when installing a Ghost 2 vehicle immobiliser. This will ensure that the device operates properly and efficiently. After the installation is completed, test the system by entering the PIN code, then turning on the engine. Regular testing will enable you to detect any issues early.
Before starting the installation, make sure you check the position of the CAN H and L wires. They are essential to power the immobiliser, so it is important that they are properly connected. It is also an excellent idea to label the wires so that it makes it easier to identify them when installing the device. Once you have identified the location of these wires, connect them to a permanent 12V power source as well as an earthing point. Make sure you utilize a fuse tap when required to shield the connections from damage or short circuits.
After connecting the wires, neaten the wiring with cable ties to avoid potential alteration. It is also a good idea to cover the wires with insulation tape or heat shrink tubing. ghost immobilisers will protect them from electrical shorts and increase the lifespan of the device. Once the wiring is secured it's a good idea test the Ghost 2 immobiliser.
The Ghost 2 immobiliser offers a service mode in situations where you may have to sell your vehicle, such as when it is being repaired or valet parked. This will disable the PIN sequence temporarily. To activate this feature, press the brake pedal while pressing the accelerator for a number of times equal to the first digit of the emergency code. The system will then enter service mode, which can be confirmed by flashing the indication signal 5 times.
It is simple to change PIN codes
It is simple to safeguard your vehicle from theft using the ghost 2 immobiliser. It is hidden inside the vehicle and is accessible only by a special code. The device is directly connected to the vehicle ECU via its data bus, and does not rely on radio frequency signals as do traditional Thatcham immobilisers, or aftermarket alarm systems. This makes it difficult for thieves to listen for the click of a conventional immobiliser relay or add new key fobs. The control unit is hidden within the vehicle's wiring harness or dashboard and cannot be physically altered to reset the system.
The ghost 2 immobiliser connects to the vehicle's CAN Data network. It makes use of buttons on the door panels, steering wheel and the center console, to create a customisable series of up to twenty button presses that need to be entered to start the engine - similar as a PIN. This unique next generation system does not require wire cutting upon installation and can be fully reprogrammed at any time. You can even set your vehicle in Service or Valet mode to allow it to start temporarily while you are giving it to a mechanic to work.
You can also make use of the app to change your PIN code, or deactivate it completely if you have lost your keys. This feature is especially helpful in the event that you have offered your car to someone else to use as a valet parking space or for servicing because it prevents them from starting your vehicle and taking it away without your consent. It's also inaccessible to professional thieves because it doesn't utilize radio frequencies or circuit cuts.
The ability of the immobiliser prevent relay thefts is another excellent feature. Relay theft is one of the most frequent methods of car theft. Criminals can hack the diagnostic ports of your car, then modify the signal sent by the car's ECU to fool it into thinking that an authentic car key is present. This is the way traditional immobilisers are removed, however with a ghost 2 immobiliser, the signal is blocked before it reaches the ECU.
Easy to use app
Ghost 2 is a revolutionary immobiliser that shields your vehicle from hacking, key-cloning and key theft. It connects to the CAN data network of your vehicle and requires an PIN code to start the engine. It also stops thieves from by using signal spoofing or device spoofing which are common methods of stealing vehicles.
The system is simple to use and functions similar to a standard car alarm. Installing the system allows you to create a unique 20-digit PIN code that must be entered before you start the vehicle. This will stop the vehicle from being taken even if your keys are removed. If you wish to disable the system, you can do so through an app on your smartphone.
Contrary to other systems that are silent, the ghost is quiet and does not emit any radio frequency signals. It is a weatherproof, discreet device that can be installed in any vehicle. It can be concealed under the dashboard, steering wheel, or even the door panels. It communicates with your ECU through the CAN data circuit, and is not affected by diagnostic tools that some thieves employ to locate security systems. It is not affected by jamming devices which can spoof codes.
It is a hidden installation that doesn't require any cutting of wires or modifications to the vehicle, and it can be used as an anti-theft system for all vehicles. Its technology has been proven to be efficient, and it's in compliance with TASSA Standards. Ghost is a great solution for classic, sports and prestige cars. It can also be used to protect vehicles that are rented out on apps like Turo.
The Autowatch Ghost 2 represents the next generation of auto immobilisers. The system is completely inaccessible to thieves, and blocks them from starting your car without your PIN, or unless they have been authorized by the app. It also does not emit radio frequencies or other signals that can be detected by scanners. The process of installing the app is simple and quick. The app is simple to navigate and offers a user-friendly interface that makes it easy to set up and use. It also includes a GPS tracker that can assist police locate the vehicle and recover it.
Easy to reset
It is possible to protect your vehicle from theft using an immobiliser ghost 2. It is integrated into your vehicle's ECU and creates a security barrier that thieves are unable to break through without the proper pin. The device is also TASSA-certified, which means that it's acknowledged by insurance companies. It's a useful tool to prevent car theft and could save you money in the long run.
In contrast to traditional alarms and immobilisers that require cutting of circuits and circuit cutting, the Ghost system is directly connected to the vehicle's CAN data network and works using your existing buttons on the dashboard and the steering wheel. You can create a unique PIN sequence, which can be up to 20 presses in length. The PIN must be entered before the engine can begin, just as with the credit card's PIN. The Ghost system is inaccessible to thieves, and there are no LEDs to indicate its presence. This makes it the most efficient aftermarket CAN-bus system available today.
The Ghost system has another benefit that it doesn't transmit radio frequency signals. This means it cannot be detected by thieves or snatched up. This helps to prevent cloned keys and relay attacks and also the more usual method of hacking a car's CAN bus system by scanning for signals from the alarm/immobiliser. In addition to that, the Ghost system is designed to be completely hidden inside your vehicle and there are no LEDs or signals to indicate its presence.
The system has a Transport Mode which disables the Ghost System. This is helpful for situations when you require a temporary deactivation of Ghost for instance, when you are transporting or maintaining your vehicle. This mode is less effective than Service Mode as it doesn't deactivate the Ghost system if you exceed 31 mph within 15 minutes.
To reset your ghost 2 immobiliser, you will need to have the emergency code, which is available from your installer. The code is typically hidden in the scratch-off section of the card that came with the installation. It is important to keep the emergency code secure and keep it in a place that is secure, such as your wallet at home.